3D PotterBot 7 Pro

4000 gif.gif
4000 gif.gif

3D PotterBot 7 Pro


3D Potterbot 7 PRO is the upgraded version of the Potterbot 7. The overall size is the same but the similarities end there. The 7 PRO utilizes a larger hybrid closed loop stepper motor on the extruder and on the Z axis.            ( Optional 4000 ml Extruder )

Add To Cart

New for 2017 - 3D Potterbot 7 Pro 

 hybrid  motor

hybrid  motor

7 PRO is capable of extruding clay at a faster rate than the standard 7 with it's standard 2000 ml extruder. Now we are able to use large diameter nozzles and extrude at much faster rates and volume.

By using a more powerful hybrid closed-loop stepper motor on the Z axis we have the ability of faster travel but more importantly we have the ability to carry heavier extruders.

This bring us to the next advantage. The 7 Pro is capable of carrying our next generation 4000 ml high performance extruder as an option. 

3D Potterbot 7 Pro is our professional dedicated ceramic and paste 3D printer. Built rugged and ready for production environment, universities and ceramic institutes.

The 3DP 7 Pro is completely redesigned to improve speed and acceleration. The design uses high-precision linear rails from IGUS, a completely new X and Y axis drive system with precision timing belt, and integrated closed loop hybrid motors. This eliminates any need for machine adjustment and reduces maintenance. Our design utilizes traveling X & Y axis with stationary Z axis. The X-axis is allowed to travel freely on top of any flat surface. The Z axis and extruder use a reduction gearbox for faster and smoother prints.

The hard anodized linear rail with advanced plastic car bushings will give extended service life, even in harsh environments. By using timing belts we have decreased printing  time by as much as 75% for small items. The closed-loop motors have on board circuitry to eliminate any missteps or inaccuracy, while increasing the precision substantially and most importantly increasing the acceleration speed.

7 uses our 2000 ml direct nozzle extruder. Because the extruder is stationary, the clay comes directly out of the nozzle without any hoses, complicated air compressors, or augers. In addition, we are able to print superior quality prints with less air bubbles, in less time, and at larger scales.

Extruder tubes can be easily loaded from any standard pug mill. You can load 5 tubes in less than 10 minutes, that is 60 pounds of clay! The tubes can also be loaded manually with clay purchased from your local ceramic supplier. Clean up is easy and can be accomplished between loading tubes in less than a couple of minutes.


This is our new touch screen Control Center. It's packed with features and options that make the stand-alone operation of our 3D Potterbot effortless. A simple SD card is inserted with the G code to run your prints. You have complete control over the printer & extruder by being able to adjust the speeds and flows easily through the touch screen. This touch screen is an integral part of our Arm core processor main controller board. (It's not an aftermarket add on). It also has network compatible (optional upgrade). This means no more USB cable, just log on to the network and you are in full control. Some of our customers are requesting standalone operation to run just the extruder. The same touch screen along with the main board can be utilized to run our extruder completely autonomous of any other device. 




Printing Envelope:

X-17" (432 mm)

Y-14" (356 mm)

Z-19" (483 mm)

Printer size: L 27"  W 26"  H 32"

Table size for full travel: 47" wide 33 deep up to 72" hight

Bat      13.5 " Dia 349mm

Height to the top of the extruder fully extended is 72 inches

Average speed: 55 mm/s max 130 mm/s

Power: Output - 24V, Input: 110-220V, 50 / 60 Hertz (no 220V power plug supplied for customers outside of USA)

Power consumption: 24 volts +/- 2 amps

Main controller board running Smoothieware with Arm processor Cortex M3 100 - 120 Mhz

Touchscreen included - full control Standalone function, input either SD card with G-code or USB cable for direct control of printer. Recommended slicing programs Simplify3D, Cura, or Repetier.